Configure your Machine+
Customer Comments about WEBER LCE+
Meridian Products – Weber LCE-2-1350 Compact & Weber LCE-3-1350 wide belt sander
New Holland, PA 17557
At Meridian Products we produce high quality kitchen cabinet components. Our doors and drawer fronts can have solid wood raised panels or veneer panels. With the old technology wide belt sanders in our panel line we were required to do a lot of hand orbital sanding to get the quality level our customers needed. We identified our requirements and researched several brands and did some live demonstrations. After traveling to NY to demo the patented CBF system we chose to purchase two Weber machines, a three head calibration sander and a two head finish sander. The machines are well built and easy to operate. We have successfully reduced our sanding labor and are producing a more consistent finish.
Trieste Corp. – Weber LCE-3-1350 CMP2, MARTIN T75 Prex, T45, T54, T27 Flex
Mr. Isaac B. Hayun, Long Island City, NY
I am building high end custom furniture and for this I needed the right machines for precise and quick results. I chose the Weber wide belt sander because it gives me the best flexibility for solid wood, veneer and lacquer/sealer sanding. With the patented Weber CBF system, I get almost no oscillation and the few marks left are removed by the patented Weber planetary brush head aggregate. The planetary head not only takes the marks away it also can sand deep into profiles and breaks the edges so that we do not need to sand by hand anymore.
I also purchased a tilting arbor MARTIN T27 Flex shaper, T45 thickness planer, T54 jointer and the T75 Prex dual-tilting sliding table saw. These machines are heavy duty and carry with them a great resale value…something that you do not see much anymore with industrial woodworking machinery.
Scott Slater – Weber Sander LCE 1350
Bespoken Woodworks, Sierra Madre, California
I have a cabinet shop in Southern California. I was in the market for a new sander and have had a few widebelt models in the past. The main reason that I was upgrading was that I needed a machine with 53” width and the ability to sand veneered panels without damage. I had previously owned a double head 43” sander with air platen and did not trust the machine when sanding veneered panels. It was always a job for hand sanding, which is expensive and time consuming.
The WEBER sander has a few features that make sanding difficult parts a breeze. First of all the machine has a segmented platen which uses 22 mm air cylinders to control the pressure of the platen. The machine also has a CBF head which creates very short sanding strokes (more on this later). When sanding veneer I want the machine to follow the variations in thickness in the panel, this is typically a very small variation but too much pressure on a high point will result in the veneer being sanded through. The WEBER uses rollers on the infeed to measure the work piece then turns on the segments in the platen based upon the settings I selected. I can control the pressure on all the edges protecting valuable materials. With a 180 grit belt I can run a veneered panel through the machine 4 times while sanding off a pencil mark on each pass before getting sand through. This was impossible with my old sander.
One place where the WEBER really shines is when doing finishing. When I have a flat piece that is going to be finished at the shop (most of my work is finished on site), I can apply the first coat of finish then set the sander up for lacquer sanding. I put in a 320 or 400 grit belt, and then run the part through. Absolutely no hand sanding is needed on the face. The part is simply cleaned off and the second coat is applied. I do this step 3 times and get exceptionally well-finished parts. The machine with variable speed on both the sanding heads and the conveyor belt is setup for lacquer sanding. The belt speed is slowed down, and the feed is sped up. With the CBF head the machine does very short sanding strokes, which does not load up the paper. The automatic belt cleaning during this program cleans the sandpaper. What happens is almost magical and the results are stunning.
The build quality of the WEBER is first class. The machine is made almost 100% at their factory in Bavaria Germany. WEBER makes metal sanding machines that are workhorses and uses this same heavy-duty construction in the wood line. The electronic parts are either Siemens or Toshiba and can be sourced overnight if the machine needs repairs (so far no issues with my sander).
I could not be happier with my purchase. I have had 2 other German sanders and neither one compares with the WEBER.
For uniform sanding quality+
The contact roller is used in the production of plain surfaces, what is also known as calibration. The spiral-shaped, grooved roller guarantees the highest degree of precision and enables large chip removal as well as ensures a long service life. The sanding pad serves to ensure improved surface quality – with solid wood and veneers. The segmented version of the sanding pad with electronic control can process tolerances up to 2 mm with the highest consistent sanding quality.
For even better sanding results+
For even more efficient operation+
For targeted sanding pressure+
A good sanding result is dependent upon reliable segmented platen technology, which adjusts the sanding pressure of individual segments to the workpiece size via electronic control. With the patented WEBER ISA version the pressure pieces and sanding lamella form one unit. This unit is maintenance-free and resistant to dirt.